[Remote] Network Design Engineer V (WAN /Job Package Engineer) ABMS Job Details | Lumen Technologies

Note: The job is a remote job and is open to candidates in USA. Lumen Technologies is a trusted network provider transforming how businesses connect in an AI-driven world. They are seeking a Network Design Engineer V to support the Department of the Air Force C3BM/ABMS program, focusing on developing and implementing secure WAN/transport solutions.ResponsibilitiesWAN Architecture & Design EngineeringDevelop WAN/transport design recommendations for mission networks: site connectivity, segmentation, resiliency, and performance engineering across classified and unclassified enclavesDefine engineering requirements, interfaces, and implementable WAN designs, including L0 circuit configurations and CLLI circuit-route options across CONUS/OCONUS; optionally address routing, addressing, QoS, encryption, and boundary protectionDevelop optimized WAN transport options using OTN and ITU‑T standards (G.709, G.798, G.872); apply MPLS/IP, Ethernet, VPN/IPsec, SD‑WAN, and modern secure access patterns (SASE/SSE) where applicablePropose WAN work package options to SAIC technical leadership to support engineering trades before implementation; deliverables may include HLD/LLD, logical/physical diagrams, IP plans, L0 routing/QoS policies, security boundary requirements, BOM/part lists, rack elevations (as applicable), configuration templates, and interface cut sheetsSupport the SAIC Chief Engineer with MOPs, implementation plans, cutover schedules, rollback procedures, and test/validation plans; participate in technical reviews and change control; identify/mitigate risks per work packageRecommend optimized WAN solutions for current/long-range planning; partner with technical leads to select tools/technologies that improve efficiency, reduce cost, and increase customer satisfactionCreate/maintain engineering and compliance evidence (device configuration baselines, DISA STIG notes/checklists, boundary descriptions, diagrams, status reports) to support audits and RMF/ATOSupport operational projects and maintenance windows; assist implementation teams during turn-ups, migrations, and service transitionsRecommend automation/standardization of repeatable engineering tasks (configuration generation, validation checks, documentation workflows) consistent with program approvalsTroubleshoot complex hardware/software/network issues (as requested); document problems, root causes, and resolutions; feed lessons learned into package templates and standardsSupport WAN capacity planning across sites/segments (bandwidth, optical/Carrier Ethernet where applicable, routing headroom, power/cooling constraints, lifecycle/EOL)Support L0 circuit delivery/integration/activation and service migrations: coordinate with providers, validate acceptance criteria, and update as-built documentationProvide inputs to design review packages; update network drawings (e.g., Visio) and route maps to reflect approved designs and as-built changesDevelop ROM estimates and cost models for new sites, routes, and WAN servicesAs requested by the PM and/or Chief Engineer, serve as technical liaison among teams to align design intent, circuit turn-up activities, and field executionProvide Tier 3/4 troubleshooting and root-cause analysis for WAN/transport issues and recommend corrective actionsSupport RMF/ATO by producing required network engineering evidence: diagrams; port/protocol/service documentation; boundary descriptions; STIG checklists/implementation notes; and as-built configurationsDeliver technical design reviews, implementation-readiness briefings, and mission-impact assessments to the SAIC Chief Engineer and operational teamsSkillsUS Citizenship is requiredActive TS/SCI or SCI EligibleIAT Level I/II/III CertificationTravel is requiredEducation/experience: BA/BS +17 years; or MS + 13 years; or PhD/JD + 10 years related experience14+ years progressive WAN/transport engineering, network architecture, or telecommunications experience, including deployable implementation/job packagesDeep expertise in OTN and ITU-T standards (G.709, G.798, G.872)Deep expertise in MPLS/IP, Ethernet, VPN/IPsec overlays, and enterprise/carrier WAN design patternsDeep expertise in Routing/traffic engineering (BGP, OSPF/ISIS), path control, convergence, SD-WAN and secure connectivity (SASE/SSE), segmentation/policy design, QoS (marking/queuing/shaping), performance engineering, capacity planningDeep expertise in Network security, boundary protections, and Zero Trust; field-ready engineering packages (logical/physical diagrams, IP plans, BOMs, config templates, implementation steps, cutover/rollback, test/validation)Task/work-order execution support: design reviews, implementation readiness coordination, and design-to-field discrepancy resolutionTechnical writing/communications: concise engineering documentation and briefings for technical and non-technical stakeholdersConsultative skills: rapport, fact-finding, requirements definition, options/recommendations, follow-through, customer focus; thrives with competing prioritiesBenefitsLumen offers a comprehensive package featuring a broad range of Health, Life, Voluntary Lifestyle benefits and other perks that enhance your physical, mental, emotional and financial wellbeing.We're able to answer any additional questions you may have about our bonus structure (short-term incentives, long-term incentives and/or sales compensation) as you move through the selection process.Company OverviewCenturyLink (NYSE: CTL) is a technology leader delivering hybrid networking, cloud connectivity, and security solutions to customers around the world. It was founded in 1968, and is headquartered in Monroe, Louisiana, USA, with a workforce of 10001+ employees. Its website is https://www.lumen.com.